Hi Kev.

What app are you using watch the video? Is this on your phone or computer?

Can you see video live from the k6 using the Innovv app?

Hi Dean, have you connected the red and black wires to a permanent feed, and the yellow to switch live?

Sorry, not on a Z1000 so can’t really help with camera placement…

Hi David.

K6 should be capable of recording 2k on front camera, but if you are happy with 1080 then that’s great.

It will also allow more recordings before the sd card is full 👍

Did you format the sd card in the camera?

That seems about right.

And the picture interference is at the same point every time you play it back?

Just trying to confirm if it’s a playback issue or recording issue…🤔

What spec is the sd card? What format are you recording in on front camera?

Also, how are you connecting the sd card to you computer?

If Innovv aren’t helpful, give me a shout and I can measure the thread sizes for you.

You could use a Fuzeblock FZ-1. It wires to battery and can give constant or switched power. You can feed 6 different accessories.

I use it for K6 (constant power), Satnav (switched power), usb socket (switched power), and heated gloves (switched power).

You will probably find downloading videos a bit slow over WiFi, and better to remove card and copy files on PC.

Therefore, you only use the WiFi for changing settings on K6.

3 mins is probably long enough to do this.

Hi David

Yes, just connect as per instructions.

Red and Black to battery or other permanent power supply. Yellow to switched power source.

Camera should start recording a few seconds after ignition is switched on, and stop a few seconds after ignition is switched off.

Adam

Good news.

Hello Bert.

How have you wired in your k6? (USB or supplied power converter?)

At start up the k6 should start recording (red light) and enable WiFi (green light). Check the instructions to see what the light sequences signify.

You can change the length of recording loop in the app, but 5 mins is longest. This makes the files easier to play and download.

Hi Dave.

The K6 will work fine without connecting to your phone (switching on and off with ignition), but obviously the app won’t work if not connected.

K6 doesn’t have Bluetooth .

Hi Nicholas.

Yes, Red and Black to battery (or permanent power), yellow to switched live.

Hi Dan.

Yes, red and black to battery (or other permanent power), yellow to a switched live.

It will draw a small amount of power when bike is switched off, but this is minimal.

If you don’t use an optimiser when bike is not used for longer periods, you could disconnect the battery.

Red and black wires should be connected to battery or other permanent power point.

Yellow wire should be connected to a switched live feed, so that the K6 can switch on and switch off correctly with ignition.

Hi Coran.

You will need to connect your K6 to a permanent live/earth feed. I assume your acc2 feed is switched with the ignition.

Can you connect to the WiFi with your phone at all?

Press button for about 3 seconds. Same to switch off.

Could it be electrical interference?

Yes, you will need to switch K6 on and off using the K6 button.

If not, you will cause corruption to the SD card, and possibly malfunction of K6.

You can’t connect the K6 to a laptop.

You have to remove microSD card and plug that into laptop.

You may need a card reader to connect the two.

It has constant power on the red and black cables.

Yellow just triggers the K6 on/off for standard functions. Otherwise it sits in sleep mode unless it detects a vibration or colision.

If google is correct, then ACC2 would be the one to use.

Can you check with multimeter? If not, then try connecting yellow wire and see if the INNOVV K6 works correctly.

Hi Brian.

The K6 should start recording without the app. It should go into record about 10 seconds after you switch on the bike.

Are your red and black cables connected to a permanent feed? And yellow to a switched feed?

Yes, your black and red cables need to be connected to a constant live.

The yellow cable is used as a signal to the K6 so it can start up and shut down correctly. (Start up takes approx 10 seconds, shut down about 25 seconds)

Also, if K6 doesn’t constant power it’ll cause issues with files and memory cards when ignition is switched off.

Yup. Speed comes gps data.

I bought K6 because I didn’t want GPS/speed data on video…

The K6 doesn’t have a GPSr module, so it can’t record any GPS metadata…

Checked all connections on the Innovv cables are tight and have good connection

Hi Richard.

First of all, double check the wiring, especially the yellow signal wire.

Also, have you updated the K6 to latest firmware ?

Finally, did you format the SD card in the camera vis the app?

Are you formatting the card in the K6?

How are viewing the cards?

With the engine running blue LED should flash.

Solid blue LED when ignition off, but good battery power.

Solid red LED when battery low.

Ah, sorry. Thought you meant you used the USB cable to supply power.

I think that might be the issue. Try switching the camera on and off manually while ignition is on. Or, use the supplied power adapter which will power the camera on and off correctly depending on ignition state.

Your USB is probably losing power too quickly so camera cannot power off correctly.

How is your camera powered?

Hi John,

Good to see the camera is actually recording.

Might be worth clearing the cache on the app. That should force it to re-populate from the camera.

I’ve not managed to fill my SD Card yet, and I have an android phone, so this is just general advice.

Are you checking the card via WiFi, or ate you putting into a computer?

App does not need to be active.

Did you see the red/green light on when starting motorcycle?

Hi Andrey.

Not good you are getting these issues.

I can run some tests on my system on Saturday and show you how it performs.

My K6 is new, and is working the way you want it to.

Adam

Glad you got it sorted.

https://innovv.com/products/innovv-k6-gopro-bracket-bagonly-for-k6-rc6-dvr-cameras?srsltid=AfmBOoqOKn1hrMe7RgiWbZGeLMWs2VDrCt8dw_NsTNAT1bYZesqIxW0G6R0&variant=44491785044176

Andrey,

Can you show exactly how you have wired the power converter?

This is not an issue with K6, as the power converter should stop supplying power after ignition is switched off.

So possible power converter issue, or system is mis-wired.

Hi Andrey.

Can you double check your voltage readings?

If the power supply is switching off and supply 0v, how can your camera still be operating and drawing power?

The power converter should continue outputing 5v for 25 seconds after ignition is switched off.

Recently install K6 on my ZZR1400.

Everything seems good, except the time and date reset everytime I switch it on, unless I connect the app.

Is this expected behaviour? Or is there a setting I need to change?

Thanks

Adam